How does NBR O - Ring perform in vacuum environments?

Nov 17, 2026

Leave a message

Industrial, aerospace and semiconductor vacuum systems place demanding requirements on sealing components. Leaks within vacuum chambers can disrupt manufacturing processes, reduce yield or render equipment inoperable. NBR (nitrile butadiene rubber) is widely considered for vacuum sealing, yet many engineers are unsure of its vacuum performance compared with other elastomers. This guide reviews core performance characteristics, tradeoffs and suitable operating boundaries for NBR O-rings in vacuum service.

First, it helps to clarify the unique demands of vacuum sealing. Unlike positive-pressure hydraulic or pneumatic systems, vacuum service relies on maintaining a stable pressure difference between the chamber interior and ambient atmosphere. Seal leak rate is critical. Outgassing (volatile substances released from the elastomer) and gas permeability (gas diffusion through the material bulk) can raise chamber pressure above the required setpoint. High-vacuum applications require very low leak rates, so material selection focused on low outgassing and low permeability is essential.

NBR is a synthetic copolymer of acrylonitrile (ACN) and butadiene. It is valued for low cost, good oil and fuel resistance and reliable mechanical performance across moderate temperature ranges. Its vacuum performance is strongly tied to ACN content. Low-ACN NBR (approximately 18–25% ACN) delivers higher elasticity but higher gas permeability, making it easier for atmospheric gases to diffuse through the seal. High-ACN NBR (35–45% ACN) is stiffer, shows lower permeability and better abrasion resistance, but has reduced low-temperature flexibility. Selecting the incorrect NBR grade for vacuum applications can lead to persistent, hard-to-diagnose leakage.

Outgassing is one of the primary limitations for NBR in vacuum. All elastomers exhibit some outgassing, but residual uncured monomers, processing oils and softening additives can vaporize under vacuum and form thin contaminant films on nearby surfaces. In semiconductor manufacturing, such deposits can contaminate wafers. Post-curing is used by qualified manufacturers to remove volatile fractions from NBR compounds, and low-outgassing NBR grades are available for general vacuum use. Even with post-cure treatment, NBR generally cannot match the low-outgassing performance of specialty elastomers such as FKM or low-outgassing silicone. Typical total mass loss values are provided in industry material guides as reference only and will vary by formulation.

Temperature is another limiting factor. Standard NBR operates reliably within roughly -40°C to 120°C. Near the upper limit, the material softens and compression set resistance declines. Vacuum environments lack convective air cooling, so component temperatures can rise faster than in positive-pressure systems and accelerate degradation. For vacuum service above 120°C, HNBR is often considered as an alternative. HNBR offers higher thermal aging resistance and an extended temperature rating. You can review our HNBR sealing options on the Hydraulic Rubber HNBR O-Ring product page.

NBR is still a practical choice for many low and rough vacuum applications. Food packaging vacuum equipment and non-UHV general laboratory vacuum setups are common fits, where pressure differential is moderate and temperatures remain mild. NBR's oil resistance and cost advantage make it suitable for these scenarios, provided low-outgassing post-cured grades are specified.

A common engineering error is repurposing standard hydraulic-grade NBR O-rings for vacuum duty. Formulations optimized for fluid power may not be controlled for outgassing or permeability. Grade selection is essential. We supply Green Colored NBR O-Ring options formulated for general low-outgassing vacuum use, precision molded to tight dimensional tolerances to support consistent sealing.

O-ring compression ratio is critical for vacuum sealing. Excessive compression creates high stress and accelerates material fatigue; insufficient compression results in leakage. NBR's elasticity supports tuning compression ratios for small-gland and compact chamber designs. Our O-ring product range covers micro O-rings for miniature vacuum hardware and large-diameter seals for industrial vacuum tanks, with NBR grades optimized for vacuum performance.

NBR is not suitable for ultra-high-vacuum (UHV) service. At UHV pressure levels, NBR's outgassing and permeability become unacceptable. UHV systems typically specify low-outgassing silicone or FKM. Encapsulated O-rings are another alternative, combining an elastomer core for flexibility with a chemically stable outer shell that suppresses outgassing and diffusion. Our Small Red Color PTFE Encapsulated Seal O-Ring is designed for compact UHV components. For higher-temperature vacuum furnaces and aerospace assemblies, our Silicone FEP PFA Encapsulated O-Ring options support service temperatures up to 200°C.

Proper installation directly impacts vacuum seal reliability. Even high-quality NBR O-rings will leak if twisted, nicked or poorly seated in the gland. Minor surface scratches create leak paths that compromise chamber pressure. We provide installation guidance alongside our seals, including recommendations for vacuum-compatible lubricants; petroleum-based lubricants should be avoided because they introduce outgassing risks.

O-ringOEM Colored Nbr Oring Pu Hnbr Fkm Silicone O Ring Rubber Seal O-ring

In summary, NBR O-rings are cost-effective for rough and moderate vacuum systems where oil resistance is required, as long as post-cured low-outgassing grades are selected. They are not recommended for ultra-high-vacuum, high-temperature vacuum or contamination-sensitive processes where minimal outgassing is mandatory. For critical systems, application review with a sealing specialist is recommended to match the material and profile to operating conditions.

If you are developing vacuum equipment and require support selecting O-rings, or need NBR or alternative vacuum sealing solutions, contact our team for an application consultation.

This guidance is built on widely accepted elastomer and sealing industry principles.

Send Inquiry
Send Inquiry